Few points on “Selection of Bolts

Bolted joints are extensively used in piping industry. Flanged joints can be thought with proper bolts. So selection of appropriate bolts plays an important role in proper joining and preventing leakage. By this article i will try to list few requirements governing the selection of bolting to complete the flanged joints. The selection criteria can be grouped into two limitation categories:

1. Physical Limitations and
2. Material Limitations.

Physical Limitations:

• Threading Requirements: All threads shall be in accordance with ASME B1.1.
• Jack Screws: Jackscrews shall be used to facilitate flange separation for maintenance. Joint assemblies which often require frequent separation include orifice plates, spectacle plates, spacers, screens, and drop-out spools. Piping layout shall be designed such that flanges can be separated without excessive force. Jackscrews shall be installed to be accessible from both sides of the pipe. For orifice flanges, jackscrews shall be installed at 3 and 9 o’clock positions. When flange separators are used, jackscrews are not required. Jack screws shall be the same material as the flange bolts.
• Bolt Selection: Bolting for flanged joints shall be selected for service by service temperature, and corrosivity of the environment.
• Bolt Lengths and Sizes: Bolt length and diameter is determined by the flange standard used. Each of the following flange standards has a method for the determination of bolt length.
• ASME B16.1, ASME B16.5, ASME B16.47, API 6A Type 6B, MSS SP-44, AWWA

• Bolt Length: Bolts shall be expressed with inch diameters, and the length in millimeters, rounded up to the nearest 5 mm.
• Flanges Not Covered: Flanges not covered by the above standards shall be considered non-standard, and bolting is to be handled on an individual basis.

Washers:

• Flat Washers: Flat washers under the nuts are required for special cases only, such as on insulating flanges and under the nuts bearing against plastic flanges.
• Belleville Washers: Belleville washers may be required for severe cyclic service, and bolt service temperatures above 450 deg C

Material Limitations

• General Process: Materials for process and general services shall be ASTM A193 Grade B7 stud bolts with ASTM A194 Grade 2H nuts for service temperatures from minus 20 to plus 450 deg C.
• Low Temperature: Materials for low temperature services shall be as follows:

1. Stud bolts conforming to ASTM A320 Grade L7 with nuts to ASTM A194 Grade 4 or 7 shall be used for bolt service temperatures from minus 18 to minus 101 deg. C.
2. ASTM A320 Grade L7M studs and A320 Grade 7M nuts may be used for low temperature services from minus 18 to minus 73°C.

• Stud bolts conforming to ASTM A320 Grade B8 with nuts to ASTM A194 Grade 8 shall be used for bolt service temperatures from minus 101 to minus 195 deg. C
• Materials for Upper Intermediate Temperature Services:

1. ASTM A193 Grade B7 or B7M studs with A194 Grade 7 or 7M nuts for services up to 450 deg. C.
2. ASTM A193 Grade B16 stud bolts with A194 Grade 7 nuts, for bolt service temperatures from 450 to 510 deg. C.

• When spiral wound gaskets are used for high temperature, the bolts must provide adequate stress to seat the gasket.

1. When B8 class 2 bolts are used for temperatures over 650°C, strain hardened bolts will be required to seat the gasket. Windings for high temperature gaskets are most likely type 347, or inconel.
2. At temperatures over 650°C, strain hardened will anneal. As long as the joint is not broken, the annealed bolts have adequate strength to hold the joint.

• Materials For Sour Service: Materials for sour services shall be as follows:

1. Standard quenched and tempered ASTM A193 Grade B7 stud bolts with 2H nuts shall be used for sour wet services when the bolting is as follows:
2. Not directly exposed to hydrogen sulfide
3. Not buried or insulated
4. Not equipped with flange protectors, or not deprived of direct atmospheric exposure.
5. ASTM A320 Grade L7 stud bolts with Grade 4 or 7 nuts can be used under the same conditions.

• Stud bolts conforming to ASTM A193 grade B7M with nuts to A194 Grade 2HM shall be used under the following conditions:

1. Direct exposure to sour environments
2. When the bolting will be buried or insulated
3. When the flange is equipped with flange protectors, or otherwise deprived of direct atmospheric exposure.
4. ASTM A320 Grade L7M bolts and Grade 7M nuts can be used under the same conditions.

• Machine Bolts: Steel machine bolts conforming to ASTM A307 Grade B may be used on flat-faced cast-iron or non-metallic flanges in non-sour environment. Nuts shall conform to ASTM A563 Grade D. This bolt and nut combination may be used in sour services when the Grade D nuts are not resulfurized. This system is also suitable when the use of “weak” bolting is specified to avoid overloading flanges. Such bolting may be zinc coated.
• Expansion and Contraction: When fluid temperatures are below minus 45 deg. C, the selection of bolting material or the bolting design shall include consideration of differential contraction between flanges and bolts such that changes in gasket seating pressure will not result in leakage. Similarly, differential expansion shall be considered at operating temperatures above 300 deg. C

The following information shall be included in the Purchase Description:

• Type of Bolt
• Fit
• Material
• Material Grade
• Size of bolt, diameter X length
• Additional requirements